Electrical fitting jobs in Warminster

Fill any gaps you have in your schedule.
Tradesman Start

Electrical fitting Jobs in Warminster (completed jobs only)

Fitting neon strip in garage
Electrical fitting job 6 miles from Warminster in Westbury
Change two light fittings
Electrical fitting job 15 miles from Warminster in Bath
Change kitchen light fittings in two separate flats (in the same building).
Storage Heater
Electrical fitting job 17 miles from Warminster in Corsham
Supply and fit replacement night storage heater.
Replace extractor fan
Electrical fitting job 26 miles from Warminster in Bristol
Replace bathroom extractor fan which is in the attic. Length of vent tube (which we have) also needs to be replaced.
8 kitchen downlights 3 not working. Earth bond needed on gas
Electrical fitting job 46 miles from Warminster in Gloucester
3 down lights not working also need earth bond on gas meter
Electric socket outside
Electrical fitting job 26 miles from Warminster in Bristol
Exterior electrical socket to be installed
replace or move old lights, and replace 2 outside light
Electrical fitting job 31 miles from Warminster in Andover
move and replace lights in house, and replace 2 outside lights and put in switch.
fix outside lights x 3
Electrical fitting job 48 miles from Warminster in Carterton
Electrical works
Electrical fitting job 33 miles from Warminster in Thornbury
Need 4 external security lights replacing. None of the three spotlights in the en suite work.
Change 2 Kitchen Lights
Electrical fitting job 31 miles from Warminster in Swindon
I want to replace old Kitchen lights with 2 new ones. I have the new lights on premises. I also want to disable the alarm on a running machine.
Fitting exterior light.
Electrical fitting job 24 miles from Warminster in Yeovil
Exterior light to be fitted to outside of garage. Garage has interior light already and two available electrical sockets. Electrical cabling for exterior light would need to be supplied.
Install an extractor fan in a bathroom
Electrical fitting job 32 miles from Warminster in Swindon
Extractor fan, through the ceiling, vented through the attic, and through the gable end of the house. I would prefer a pull cord on / off switch than an isolator switch outside the bathroom. Happy with a standard fan, but would like a quiet one. Attic is easily accessible.
Connect underfloor heating thermostat to mains
Electrical fitting job 29 miles from Warminster in Malmesbury
The bathroom in our top floor flat is being refurbished. Insulation boards and an under-tile heating cable have been laid and are ready for testing and connection to the mains. The cable is still exposed and has not been sealed in or tiled over yet. The cable was attached to fibreglass matting but the shape of the bathroom made the matting unusable, so the cable was detached from the matt and laid on its own, but following the manufacturer’s instructions on laying loose portions of the same cable. All our existing circuits run from a consumer unit, through the roof space and down the internal partition walls which are all metal stud and plasterboard. We have roof space access if we need to run a new circuit back to the consumer unit which is approximately 4 metres away from the thermostat at the opposite end of a corridor. However the consumer unit is on an exterior wall and so the roof space access above it is very restricted. It’s tight to the eaves and enclosed by a fire barrier. It would be quite tricky to get through to the consumer unit position in the roof space, with almost no room to work when you get there. Although obviously we’d prefer not to have a visible cable running down the corridor if we can avoid it. If possible connecting to an existing circuit via a fused spur would be much easier, but I don’t know if this is allowed? The heating cable is 2 square metres of 150W cable so only 300W. We have an LCD programmable thermostat and a back box for it that hasn’t been fitted yet. The heating mat cable and sensor have been run back to an approximate thermostat location outside the bathroom. At the moment the cables are just hanging out the wall, we haven’t made any cut-outs in case anything needs to move. The thermostat position is close to various existing circuits which serve the electric central heating, heating programmer, towel rail, sockets etc. What we need is someone to advise and then make a suitable connection to the mains and test the heating before we tile over it. Must be part P registered and include to issue the paperwork to building control, and sign off the warranty for the heater.
Bathroom Fan
Electrical fitting job 48 miles from Warminster in Basingstoke
My bathroom extractor fan needs a new fuse
points and swiches in kitchen
Electrical fitting job 36 miles from Warminster in Dursley
New kitchen/utility room needs 5 extra double points 2 isolating switch points for cooker and 5 lights and switches wired. I will carry out wall chasing for trunking and making holes in wall for boxes, so just need wiring connected and certified so must be Part P.
light fittings
Electrical fitting job 41 miles from Warminster in Southampton
To wire 5 sets of light fittings in lounge, dining room, 2 in hallway and landing.
2 wall heaters and door intercom not working
Electrical fitting job 158 miles from Warminster in Manchester
2 wall heaters - that lay back to back on each side of a wall - will not turn on. This issue has occurred before and at that time, it was a broken wire to the main fuse box (close by). Also, the intercom buzzer doesn’t work in the upstairs unit but again, this happened before and the issue was a wire connecting to the fuse box.
Replace isolator switch on hot tub
Electrical fitting job 101 miles from Warminster in Hinckley
Corroded isolator switch feeding hot tub needs replacing
Power point to boiler dead so might need new wire
Electrical fitting job 160 miles from Warminster in Salford
The switch to turn my boiler on not working. Think it might need a new wire.
double oven the lower part not working
Electrical fitting job 86 miles from Warminster in Chiswick
It Siemens double oven it is working just before trying to change the connection by ammeter he did not know how to do it but the oven has no problem